Why does a brand-new 4K TV sometimes look softer and slower than the display it replaced? In many homes, the culprit isn’t the panel, the streaming app, or the console. It’s a single HDMI setting that ships switched off. Sony calls it Enhanced format, LG calls it HDMI UHD Deep Color, and Samsung calls it Input Signal Plus. Different names, same job: raising the bandwidth ceiling on a specific HDMI port so the TV will accept the full signal a modern device can send. (HDMI)
This guide explains what the setting actually changes, why manufacturers hide it, which devices need it, and the mistakes that cause black screens and flicker after people flip it on.
What the HDMI Enhanced Format Setting Actually Does
Every HDMI port has a bandwidth limit, and the TV’s firmware decides how much of that limit to expose. In its default “standard” mode, an input accepts the conservative signal set that has worked reliably since the early HDMI days. That’s roughly 4K at 30 Hz, or 1080p at 60 Hz, with no HDR and limited color detail.
Switch the port to enhanced mode and the TV allows the higher-bandwidth signal types. According to Sony’s own support documentation, selecting Enhanced format on a compatible input enables signals such as 4K at 60p in 4:4:4, 4:2:2, and 4:2:0 chroma at 10-bit color depth. Those numbers matter because they are the building blocks of HDR video and crisp desktop text.
The underlying standard is HDMI 2.1, published by the HDMI Licensing Administrator in 2017 and updated as 2.1a in 2022. That specification defines the higher-bandwidth modes, including fixed rate link signaling, 4K at 120 Hz, and 8K at 60 Hz. The TV setting is the gatekeeper that decides whether your port is allowed to negotiate any of it. (HDMI Specification Overview)
Here’s the practical translation. With the setting off, a PlayStation 5 or a gaming PC may quietly drop to 4K at 60 Hz or lower, lose HDR, or fall back to reduced chroma sampling. With it on, the same hardware can deliver the full experience. Nothing about the panel changes. The port simply stops throttling itself.
Why TVs Ship With It Turned Off

It looks like a baffling default. Why would a manufacturer sell a 4K 120 Hz television and then cap the ports?
The answer is compatibility. Enhanced mode widens the range of signals the port will accept, and not every HDMI cable or source device can carry those signals cleanly. A decade-old cable, a cheap wall-plate extension, or an aging set-top box may produce dropouts, sparkles, or a blank screen when the port opens up. LG’s support documentation for HDMI UHD Deep Color notes plainly that some devices may not display correctly with the setting enabled.
Manufacturers therefore ship conservative and let the buyer opt in. It’s a support-cost decision, not a conspiracy. The side effect is that a large share of TVs in living rooms are running below their capability, often for years, because nobody ever opened the menu.
What Each Brand Calls It and Where to Find It
The naming varies by brand and sometimes by model year, which is why searching for the feature can feel like chasing a ghost. The table below maps the common names and menu locations.
| Brand | Setting name | Typical menu path |
|---|---|---|
| Sony | Enhanced format (some models add Enhanced format (Dolby Vision)) | Settings > Watching TV > External inputs > HDMI signal format |
| LG | HDMI UHD Deep Color | Settings > General > Devices > HDMI Settings |
| Samsung | Input Signal Plus | Settings > General > External Device Manager > Input Signal Plus |
| Panasonic | HDMI HDR Setting or Mode 2 | Settings > HDMI settings |
| Hisense and TCL | HDMI Mode, Enhanced, or 2.0/2.1 toggle | Settings > Channels and Inputs > HDMI |
Two details trip people up constantly. First, the setting is per input, not global. Enabling it on HDMI 1 does nothing for the console plugged into HDMI 3. Second, several brands offer more than one enhanced tier. Sony documents a separate Enhanced format (Dolby Vision) option on some models that turns on Dolby Vision for that input but can restrict other signal types. If Dolby Vision content looks wrong after you enable it, try the standard enhanced option instead.
Which Devices Actually Need It
Not every source benefits. A basic Blu-ray player or an old cable box will look identical either way. The setting earns its keep with hardware that can push high-bandwidth signals.
Game consoles
PlayStation 5 and Xbox Series X both need enhanced mode to reach 4K at 120 Hz, and often to enable HDR or variable refresh rate at all. If a console reports that your TV doesn’t support 120 Hz, the port setting is the first thing to check.
Gaming PCs
This is where the difference is most visible. A PC running 4K at 60 Hz in 4:2:0 chroma produces blurry, color-fringed text. With enhanced mode and a proper cable, the same PC can run 4K at 60 Hz in full 4:4:4, and small fonts snap into focus. Desktop users notice this immediately.
Streaming sticks and 4K players
Devices like an Apple TV 4K, a Chromecast, or a 4K Blu-ray player need the bandwidth for HDR10 and Dolby Vision. Without that bandwidth, HDR may silently fall back to SDR, and the picture looks flat without any error message.
Soundbars and AV receivers
This one is easy to forget. If audio runs through a receiver and then to the TV, both the receiver’s input and the TV’s port may need enhanced mode. A receiver passing 4K HDR through a standard-mode TV port is a classic source of “why is my picture washed out” complaints.
How to Turn It On Without Breaking Anything
The procedure is short, but order matters.
- Identify the exact HDMI port your device uses. Check the label printed next to the connector.
- Open the TV’s input or external device menu and find the signal format option for that specific port.
- Switch it from Standard to Enhanced, Input Signal Plus, or Deep Color, depending on the brand.
- Power-cycle both the TV and the source device. Many handshake failures clear only after a full restart.
- On the source device, re-run display setup. On a PS5, go to Screen and Video and check the 120 Hz and HDR readouts. On a PC, open display settings and confirm the refresh rate and color format.
- Play real content for ten minutes and watch for flicker, sparkles, or dropouts.
If the screen goes black after step 3, don’t panic. That usually means the cable can’t carry the wider signal. Swap in a certified high-speed or Ultra High Speed HDMI cable, keep the run short, and try again.
The Mistakes That Cause Most Problems
A few errors account for nearly every complaint about this setting.
Assuming one switch covers the whole TV. It doesn’t. Each port is independent, and people routinely enable HDMI 1 while their console sits in HDMI 4.
Blaming the TV for a bad cable. Enhanced mode exposes cable weaknesses that standard mode hides. A cable that worked fine at 4K 30 Hz can fail at 4K 120 Hz. Look for certified cables, and avoid long passive runs behind walls.
Enabling every tier at once. If your model offers both a standard enhanced option and a Dolby Vision variant, test them separately. One may restrict signal types the other allows.
Forgetting the receiver. When a soundbar or AV receiver sits in the chain, every link needs the setting, not the TV alone.
Ignoring the source menu. The TV allows the signal, but the console or PC still has to send it. Re-run the device’s display setup after changing the TV, or it may keep using the old, conservative configuration.
There’s a related trap worth knowing about. Modern TVs and devices sometimes misreport what they can do, and AI-driven picture processing can add its own confusion. The same “why is this behaving oddly” instinct applies when a smart assistant confidently states something false; our explainer on why AI makes up information covers that pattern well. With displays, the fix is always the same: check the actual signal readout rather than trusting a label.
Enhanced Format and Picture Quality: What You Will and Won’t See
Set expectations honestly. Enhanced mode does not improve color accuracy, contrast, or motion handling. It removes a bottleneck so the panel can receive what the source sends.
What you will likely notice:
- Sharper text and UI elements on a PC, thanks to full 4:4:4 chroma
- HDR that actually engages, with brighter highlights and deeper shadows
- Smoother motion in 120 Hz games
- Fewer “mode not supported” errors from modern devices
What you won’t notice: a dramatic change while watching a standard cable channel or an old DVD. Those signals never needed the extra bandwidth.
Picture quality also depends on settings beyond the port. If you are tuning a display for photography or realistic video, the choices around Leonardo AI settings for photorealistic images follow a similar logic: the defaults are conservative, and the gains come from deliberately matching settings to the source. The HDMI port is just the first link in that chain.
When to Leave It Off
Enhanced mode isn’t automatically the right choice. Leave a port in standard mode if it feeds an older device that misbehaves when the bandwidth opens up, if the cable run is long and unverified, or if you simply never use high-bandwidth content on that input. A guest-room TV showing cable news does not need 4K at 120 Hz.
There’s also a stability argument. Some devices negotiate poorly in enhanced mode and produce intermittent handshake failures, especially through switches and splitters. If a port works perfectly in standard mode and the content doesn’t demand more, there’s no prize for flipping the switch.
Conclusion
The HDMI enhanced format setting is one of the highest-value menu toggles on a modern TV, and one of the least discovered. It doesn’t make a bad panel good, and it won’t rescue a weak cable. What it does is stop the television from throttling a port that was built to handle more. Sony’s Enhanced format, LG’s HDMI UHD Deep Color, and Samsung’s Input Signal Plus all do the same fundamental job: they raise the bandwidth ceiling so HDR, full color detail, and high frame rates can reach the screen.
The practical routine is simple. Find the port your best device uses, enable the enhanced setting for that input only, restart both ends, and verify the result in the source device’s display menu. If the picture drops out, suspect the cable before the TV. Do that once, and the setting quietly disappears into the background where it belongs, doing its job every time you press play.
Frequently Asked Questions
What does HDMI enhanced format actually do?
It raises the bandwidth limit on a specific HDMI port so the TV accepts higher-quality signals. That includes 4K at higher frame rates, 10-bit color, HDR, and full 4:4:4 chroma. Without it, many devices fall back to lower refresh rates or reduced color detail, often without telling you.
Is it safe to leave enhanced format on all the time?
Yes, for ports connected to modern devices and good cables. The setting doesn’t damage anything. The only risk is instability with older hardware or marginal cables, which can cause dropouts or a blank screen. If a port is stable with the setting on, there’s no reason to turn it off.
Why did my screen go black after enabling it?
A black screen almost always means the cable or the source device can’t handle the wider signal. The TV is now asking for more than the link can carry. Try a certified high-speed or Ultra High Speed HDMI cable, shorten the run, and power-cycle both devices before concluding the TV is faulty.
Do I need to enable it on every HDMI port?
Only on the ports that carry high-bandwidth devices. The setting is per input, so enabling it on HDMI 1 does nothing for a console in HDMI 3. Check the label next to each connector and enable only the ones you need, which also avoids unnecessary compatibility headaches.
Does enhanced format improve regular TV and streaming?
Rarely for standard cable channels, but often for 4K streaming. HDR10 and Dolby Vision need the extra bandwidth, so a streaming stick on a standard-mode port may silently deliver plain SDR. If your 4K HDR shows look flat, this setting is a likely reason.
What’s the difference between enhanced format and Dolby Vision mode?
Enhanced format allows higher bandwidth generally. A separate Dolby Vision variant, found on some Sony models, turns on Dolby Vision on that input but may restrict other signal types. If Dolby Vision content misbehaves, switch to the standard enhanced option and compare.


